Adhesives (Hot Melt etc.)

Choose from our recommended Grades below
using the drop down menu

LP1020P Fully Refined Powder – Lowest Viscosity

LP1020P is our Lowest Viscosity (10-20 cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for the Lowest Viscosity requirement. Other options in our range include LP1040P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.
  This range of Fully Refined Waxes can also find applications in :-
  • PVC Compounding/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
 

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-20cpsASTM D3236
Dropping Point 113 to 118ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Melting Point 94,119 ºCDSC Peak
Whiteness Index (WI)>=45ASTM E313

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1020P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1020P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040P Fully Refined Powder – Medium Viscosity

LP1040P is our Medium Viscosity (20-40cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

 

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. Other options in our range include LP1020P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.

This range of Fully Refined Waxes can also find applications in :-

  • PVC Compounding/Masterbatch/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
   

Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 20-40cpsASTM D3236
Dropping Point 113-116ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Whiteness Index (WI)>=45ASTM E313

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1040P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1040P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040T ‘Active Flow’ – Medium Viscosity in Pastille Form (Easy Handling)

LP1040T ''Active Flow'' is our Medium Viscosity (15-40cps) Fully Refined HDPE derived wax offered in the form of white Pastilles.  

Applications and Benefits include:-

  • Processing Aid/Additive for Film Extrusion/Extrusion Blow Moulding/Injection Moulding - Key Benefits include :- Easy to Handle (Dust Free)/Low Viscosity/Good Heat Stability/Highly Compatible with Polyolefin/Improve Flowability & Productivity/ Improve Colour Dispersion/ Reduce Processing Temperature and FDA compliant!
  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. It is easy to handle (Pastilles) and will be ''Dust Free'' as its not in powder form.  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance
Other applications include :- PVC Compounding (External Lubricant for Rigid PVC)/Masterbatch/Thermoplastic Road Marking (reduce Viscosity of Hydrocarbon based formulations)  /Cable Filling/Rubber Compounding Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 15-40cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness<=2d-mmASTM D1321
Dropping Point 113 to 118ºCASTM D3954
Whiteness Index (WI)>= 20 ASTM E313

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1040T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1040T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1024P Super Refined Powder Grade

LP1024P is a ''Super Refined''  PE wax derived from an HDPE process in the form of white powder. Consequently it is an extremely clean, Low Viscosity (10-40 cps) pretty hard (Penetration Index <1) Wax that has found admirers in the Hot Melt Adhesive Industry.   

Key Benefits recognised in the Hot Melt Adhesive Application include:-

  • Very Low Volatiles due to the Double Refining Process
  • Low Viscosity which promotes wettability
  • Adjust Open and Set time
  • Enhanced heat resistance - Best in Class Thermal Resistant grade with higher dropping point and hardness than other PE Waxes
 
  • Partial replacement of FT wax (e.g. m-PO base HMA for Packaging applications) for overall cost reduction.

This grade is also used in the Paints/ Coatings/Inks Industry in its Micronised form (Please ask for details)

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-40cpsASTM D3236
Dropping Point 116 to 120ºCASTM D3954
Penetration Hardness<=1d-mmASTM D1321
Density0.95g/cm3ASTM D1505
Whiteness Index>=45ASTM E313

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchMicronised WaxPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1024P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1024P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1022P Fully Refined Powder (Wide Viscosity)

LP1022P is a Wide Viscosity (<=60cps) Fully Refined HDPE derived wax offered in the form of white powder. As the Viscosity is not so controlled it is more economical than other Fully Refined Grades.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade if their process will allow a Wax with a Wider -  less controlled Viscosity Band.

Other Applications Include:-

  • PVC Compounding/Colour and Black Masterbatch/Thermoplastic Road Marking/Petroleum Wax Blending/Cable Filling Compound
Features of the Grade are: Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC <=60cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness2d-mmASTM D1321
Dropping Point 116ºCASTM D3954
Whiteness Index (WI)>=40 ASTM E 313

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1022P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1022P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1400T – Fully Refined Pastilles – High Viscosity

LP1400T is a High Viscosity (300-400cps) Fully Refined HDPE derived wax offered in the form of white pastilles (Odorless).  

Applications and Benefits include:-

  • PVC Compounding/Filler & Colour Masterbatch/Cable Filling Compound/Thermoplastic Road Marking

Other Applications Include:-

  • Hot Melt Adhesive 
 

Main Benefits to note:  Capable of undergoing High Shear/Odorless/No Dust (pastille form)/ FDA approval

Features of the Grade are: High Viscosity - so capable of undergoing ''high shear''/Odorless/ Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties and Fully compliant with Many Regulations including FDA/REACH/RoHS etc. etc.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 300-400cpsASTM D3236
Dropping Point 116ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.94g/cm3ASTM D1505

APPLICATIONS

Adhesives (Hot Melt etc.)Cable Filling CompoundsCandleMasterbatchPetroleum Wax BlendPlastics & PolymersPVC ProcessingRoad MarkingRubber Modification

Packaging & Storage

LP1400T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1400T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2020P Powder

WD2020P is the Lowest Viscosity (200 cps) grade of our Virgin thermally cracked LDPE waxes

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers.  Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier  - Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding 
   

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @140ºC 150-250cpsASTM D3236
Softening Point 107ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.92g/cm3ASTM D1505

APPLICATIONS

Adhesives (Hot Melt etc.)MasterbatchPVC ProcessingRubber Modification

Packaging & Storage

WD2020P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

WD2020P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2040P Powder

WD2040P is a Virgin High Quality LDPE Medium Viscosity (400 cps) thermally cracked polyethylene wax - Very Popular in Masterbatch and Hot Melt Adhesive Applications

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers.  Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier  - Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding 
         

DATA SHEET

TYPICAL PROPERTIESVALUEUNITTEST METHOD
Viscosity @140ºC 350-450cpsASTM D3236
Softening Point 109ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.92g/cm3ASTM D1505

APPLICATIONS

Adhesives (Hot Melt etc.)MasterbatchPVC ProcessingRubber Modification

Packaging & Storage

WD2040P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2110P Powder

WD2110P - Highest Viscosity (1100 cps) and Mol Weight (2975 Mn) of any of our Virgin thermally cracked LDPE wax grades

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers. The high Viscosity and Mol Wt will help aid dispersion on highly loaded products. Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier - E.G. Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding
   

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @140ºC 1000-1200cpsASTM D3236
Softening Point 110ºCASTM D3954
Penetration Hardness1d-mmASTM D1321
Density0.92g/cm3ASTM D1505

APPLICATIONS

Adhesives (Hot Melt etc.)MasterbatchPVC ProcessingRubber Modification

Packaging & Storage

WD2110P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

WD2110P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

CS-52N

CS-52N is a Polypropylene Wax of  the Homopolymer type. It has a low viscosity of 180cps. It is suitable for paper applications as a surface modifier. It  improves abrasion and heat resistance in printing ink. It can also be used as a release agent in toners.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @170ºC 180±50cpsCOS-T-040
Softening Point 161±3ºCCOS-T-050
Hardness @25ºC (77F)Max 1.0 d-mmCOS-T-020
Density0.89g/ccCOS-T-030
AppearanceWhite powder-Visual

APPLICATIONS

Adhesives (Hot Melt etc.)Colour Concentrate (Dispersion Agent)Inks & Paints

Packaging & Storage

CS-52N is packaged in 25kgs PP Woven Bags and is supplied on shrink-wrapped pallets of 1200kgs each.

Product Safety

CS-52N is regarded as non-hazardous when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

Please contact us for compliance data.

CS-525N

CS-525N is our highest viscosity wax of 1200cps. It can used as surface modifier for paper. It is also suitable for improving abrasion and heat resistance for printing ink.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @170ºC1200±100cpsCOS-T-040
Softening Point 163±3ºCCOS-T-050
Hardness @25ºC (77F)Max 1.0 d-mmCOS-T-020
Density0.89g/ccCOS-T-030
AppearanceWhite powder-Visual

APPLICATIONS

Adhesives (Hot Melt etc.)Colour Concentrate (Dispersion Agent)Inks & Paints

Packaging & Storage

CS-525N is packaged in 25kgs PP Woven Bags and is supplied on shrink-wrapped pallets of 1200kgs each.

Product Safety

CS-525N is regarded as non-hazardous when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

Please contact us for compliance data.

CS-52NC

CS-52NC is a Ethylene - Propylene Copolymer Wax (PP Copolymer)

These Waxes are are typically used in adhesives and water-based coatings applications :- Paper industry as a surface modifier and to improve durability /Release agent in toners for plain paper /Hot-melt adhesives where it improves heat resistance and flowability.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @170ºC 180±50cpsCOS-T-040
Softening Point 150±3ºCCOS-T-050
Hardness @25ºC (77F)Max 1.0 d-mmCOS-T-020
Density0.89g/ccCOS-T-030
AppearanceWhite powder-Visual

APPLICATIONS

Adhesives (Hot Melt etc.)Colour Concentrate (Dispersion Agent)Inks & Paints

Packaging & Storage

CS-52NC is packaged in 25kgs PP Woven Bags and is supplied on shrink-wrapped pallets of 1200kgs each .

 

Product Safety

CS-52NC is regarded as non-hazardous when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data.

 

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

Please contact us for compliance data.

CS-53NC

CS-53NC is a Low Viscosity Ethylene - Propylene Copolymer Wax (PP Copolymer)

These Waxes are are typically used in adhesives and water-based coatings applications :- Paper industry as a surface modifier and to improve durability /Release agent in toners for plain paper /Hot-melt adhesives where it improves heat resistance and flowability.        

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @170ºC 100±50cpsCOS-T-040
Softening Point 148±3ºCCOS-T-050
Hardness @25ºC (77F)Max 1.0 d-mmCOS-T-020
Density0.89g/ccCOS-T-030
AppearanceWhite powder-Visual

APPLICATIONS

Adhesives (Hot Melt etc.)Colour Concentrate (Dispersion Agent)Inks & Paints

Packaging & Storage

CS-53NC is packaged in 25kgs PP Woven Bags and is supplied on shrink-wrapped pallets of 1200kgs each.

Product Safety

CS-53NC is regarded as non-hazardous when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

Please contact us for compliance data.

A100 (C5)

A100 is a straight C5 (Aliphatic) Tackifying Resin.  Its a General Purpose Grade suitable for Pressure Sensitive Adhesives (PSA) based on Natural Rubber.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point100°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity220cps
Molecular Weight3600Mw

APPLICATIONS

Adhesives (Hot Melt etc.)Road Marking

Packaging & Storage

A100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

K100 (C5)

K100 is a standard grade of Aliphatic Hydrocarbon Resin suitable for adhesives based on SIS.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point101°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity170cps
Molecular Weight2900Mw

APPLICATIONS

Adhesives (Hot Melt etc.)Road Marking

Packaging & Storage

K100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

M100 (C5)

M100 is a standard grade of Aliphatic Hydrocarbon Resin suitable for adhesives based on SIS.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point95°C
Colour4G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity100cps
Molecular Weight2700Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

M100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

R100 (C5)

R100 is a standard grade of Aliphatic Hydrocarbon Resin suitable for adhesives based on SIS.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point96°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity120cps
Molecular Weight2200Mw

APPLICATIONS

Adhesives (Hot Melt etc.)Road Marking

Packaging & Storage

R100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

 

D100 (C5/C9)

D100 is suitable for hot-melt adhesives and adhesive tape and it offers high flexibility and tackiness. It has compatibility with SBR and EVA.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point99°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity140cps
Molecular Weight2700Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

D100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

N180 (C5/C9)

N180 is suitable for hot-melt adhesives based on SIS. It offers excellent tackiness.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point80°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity60cps
Molecular Weight2000Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

N180 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

S100 (C5/C9)

S100 is a pure C5/C9 suitable for adhesives based on SIS and it offers a well balanced performance to adhesives.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point94°C
Colour4G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity90cps
Molecular Weight2600Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

S100 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

S195 (C5/C9)

DATA SHEET

PROPERTYVALUEUNIT
Softening Point94°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity100cps
Molecular Weight2400Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

S195 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

U185 (C5/C9)

U185 is suitable for hot-melt adhesives and adhesive tape and it offers high flexibility and tackiness. It has compatibility with SBR and EVA.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point86°C
Colour3G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity75cps
Molecular Weight2150Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

U185 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

U190 (C5/C9)

U190 is a pure C5/C9 suitable for adhesives based on SIS and it offers a well balanced performance to adhesives.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point89°C
Colour4G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity80cps
Molecular Weight2700Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

U190 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

E200SN (C5/C9)

E200SN offers excellent adhesion and it is suitable for rubber-type adhesives.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point102°C
Colour3G.N.
Acid Value1.5mgKOH/g
Melt Viscosity210cps
Molecular Weight4600Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

E200SN is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

G100B (C5/C9)

G100B is a Quintone grade suitable for  rubber modification and hot-melt adhesive applications.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point100°C
Colour6G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity130cps
Molecular Weight2300Mw

APPLICATIONS

Adhesives (Hot Melt etc.)Rubber Modification

Packaging & Storage

G100B is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

G115 (C5/C9)

G115 is a Quintone grade suitable for EVA hot-melt adhesives.

DATA SHEET

PROPERTYVALUEUNIT
Softening Point115°C
Colour7G.N.
Acid Value<0.1mgKOH/g
Melt Viscosity350cps
Molecular Weight4200Mw

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

G115 is packaged in 25kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets. We can also supply this product in bulk inside 500kgs bags measuring 1300mmx1300mmx900mm with a loading quantity of 20MT/40FCL.

Product Safety

Quintone Hydrocarbon Resin can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : Please contact us for information on FDA status for this Grade.

3421 (L)

The Quintac 3421 is a standard grade for hot melt Pressure Sensitive Adhesives.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Polymer StructureLinear--
Styrene Content14% Abbe's refractmeter
SI Diblock Content26%Converted by Gel permeation chromatography
Solution Viscosity1.4Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index10g/10min.ASTM D-1238 (G Condition)
Hardness33Shore AASTM D-2240
300% Modulus0.8MPaATSM D-638 (modified)
Tensile Strenght19MPaATSM D-638 (modified)
Elongation1400%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

3421 is packaged in 20kgs 3 ply paper bags and it is supplied on shrink-wrapped pallets.

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3433N (L)

Quintac 3433N is a Linear (L) SIS rubber. It's a somewhat Special grade designed for Pressure Sensitive Adhesives to give high carton sealability.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Polymer StructureLinear--
Styrene Content16% Abbe's refractmeter
SI Diblock Content56%Converted by Gel permeation chromatography
Solution Viscosity0.81Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index12g/10min.ASTM D-1238 (G Condition)
Hardness31Shore AASTM D-2240
300% Modulus0.5MPaATSM D-638 (modified)
Tensile Strenght11MPaATSM D-638 (modified)
Elongation1500%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3450 (R)

3450 is a Quintac grade suitable for Hot Melt Adhesives.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Polymer StructureRadial--
Styrene Content19% Abbe's refractmeter
SI Diblock Content30%Converted by Gel permeation chromatography
Solution Viscosity0.55Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index15g/10min.ASTM D-1238 (G Condition)
Hardness44Shore AASTM D-2240
300% Modulus1.4MPaATSM D-638 (modified)
Tensile Strenght13MPaATSM D-638 (modified)
Elongation1100%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3460

3460 is a Quintac grade suitable for Hot Melt Adhesives.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Styrene Content25% Abbe's refractmeter
SI Diblock Content-%Converted by Gel permeation chromatography
Solution Viscosity0.38Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index11g/10min.ASTM D-1238 (G Condition)
Hardness55Shore AASTM D-2240
300% Modulus1.8MPaATSM D-638 (modified)
Tensile Strenght6MPaATSM D-638 (modified)
Elongation960%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3520 (L)

3520 is a Quintac grade for Pressure Sensitive Adhesives where it provides high carton sealability.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Polymer StructureLinear--
Styrene Content15% Abbe's refractmeter
SI Diblock Content78%Converted by Gel permeation chromatography
Solution Viscosity1.1Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index7g/10min.ASTM D-1238 (G Condition)
Hardness21Shore AASTM D-2240
300% Modulus0.3MPaATSM D-638 (modified)
Tensile Strenght2MPaATSM D-638 (modified)
Elongation2000%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3620 (H)

H = Hybrid Polymer Structure. The Quintac 3620 is a standard grade for hot melt Pressure Sensitive Adhesives.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Polymer StructureHybrid (mix of Linear and Radial structure)--
Styrene Content14% Abbe's refractmeter
SI Diblock Content12%Converted by Gel permeation chromatography
Solution Viscosity1.5Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index9g/10min.ASTM D-1238 (G Condition)
Hardness36Shore AASTM D-2240
300% Modulus0.9MPaATSM D-638 (modified)
Tensile Strenght24MPaATSM D-638 (modified)
Elongation1300%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Packaging & Storage

3620 is packaged in antistatic 500kgs bags.

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

3620 Powder

The Quintac 3620 in Powder form is micronised 3620 and it is a is a grade suitable  for hot melt Pressure Sensitive Adhesives.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Styrene Content14% Abbe's refractmeter
SI Diblock Content-%Converted by Gel permeation chromatography
Solution Viscosity1.5Pa*sBrookfield Viscometer (25wt%, solids toluene solution at 25°C)
Melt Index9g/10min.ASTM D-1238 (G Condition)
Hardness36Shore AASTM D-2240
300% Modulus0.9MPaATSM D-638 (modified)
Tensile Strenght24MPaATSM D-638 (modified)
Elongation1300%ATSM D-638 (modified)

APPLICATIONS

Adhesives (Hot Melt etc.)

Product Safety

Quintac Thermoplastic Elastomers can accumulate electrostatic charges during unloading and transport which may cause flash fire when treated in presence of volatile or flammable materials. Ground all equipment and pour the product slowly into chute or vessel under inert gas. Avoid storing in wet or sunny conditions. Avoid ignition sources. Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request.