Petroleum Wax Blend

Choose from our recommended Grades below
using the drop down menu

LP1020P Fully Refined Powder – Lowest Viscosity

LP1020P is our Lowest Viscosity (10-20 cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for the Lowest Viscosity requirement. Other options in our range include LP1040P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.
  This range of Fully Refined Waxes can also find applications in :-
  • PVC Compounding/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
 

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-20cpsASTM D3236
Dropping Point 113 to 118ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Melting Point 94,119 ºCDSC Peak
Whiteness Index (WI)>=45ASTM E313

Packaging & Storage

LP1020P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1020P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040P Fully Refined Powder – Medium Viscosity

LP1040P is our Medium Viscosity (20-40cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

 

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. Other options in our range include LP1020P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.

This range of Fully Refined Waxes can also find applications in :-

  • PVC Compounding/Masterbatch/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
   

Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 20-40cpsASTM D3236
Dropping Point 113-116ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Whiteness Index (WI)>=45ASTM E313

Packaging & Storage

LP1040P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1040P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040T ‘Active Flow’ – Medium Viscosity in Pastille Form (Easy Handling)

LP1040T ''Active Flow'' is our Medium Viscosity (15-40cps) Fully Refined HDPE derived wax offered in the form of white Pastilles.  

Applications and Benefits include:-

  • Processing Aid/Additive for Film Extrusion/Extrusion Blow Moulding/Injection Moulding - Key Benefits include :- Easy to Handle (Dust Free)/Low Viscosity/Good Heat Stability/Highly Compatible with Polyolefin/Improve Flowability & Productivity/ Improve Colour Dispersion/ Reduce Processing Temperature and FDA compliant!
  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. It is easy to handle (Pastilles) and will be ''Dust Free'' as its not in powder form.  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance
Other applications include :- PVC Compounding (External Lubricant for Rigid PVC)/Masterbatch/Thermoplastic Road Marking (reduce Viscosity of Hydrocarbon based formulations)  /Cable Filling/Rubber Compounding Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 15-40cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness<=2d-mmASTM D1321
Dropping Point 113 to 118ºCASTM D3954
Whiteness Index (WI)>= 20 ASTM E313

Packaging & Storage

LP1040T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1040T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1024P Super Refined Powder Grade

LP1024P is a ''Super Refined''  PE wax derived from an HDPE process in the form of white powder. Consequently it is an extremely clean, Low Viscosity (10-40 cps) pretty hard (Penetration Index <1) Wax that has found admirers in the Hot Melt Adhesive Industry.   

Key Benefits recognised in the Hot Melt Adhesive Application include:-

  • Very Low Volatiles due to the Double Refining Process
  • Low Viscosity which promotes wettability
  • Adjust Open and Set time
  • Enhanced heat resistance - Best in Class Thermal Resistant grade with higher dropping point and hardness than other PE Waxes
 
  • Partial replacement of FT wax (e.g. m-PO base HMA for Packaging applications) for overall cost reduction.

This grade is also used in the Paints/ Coatings/Inks Industry in its Micronised form (Please ask for details)

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-40cpsASTM D3236
Dropping Point 116 to 120ºCASTM D3954
Penetration Hardness<=1d-mmASTM D1321
Density0.95g/cm3ASTM D1505
Whiteness Index>=45ASTM E313

Packaging & Storage

LP1024P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1024P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1022P Fully Refined Powder (Wide Viscosity)

LP1022P is a Wide Viscosity (<=60cps) Fully Refined HDPE derived wax offered in the form of white powder. As the Viscosity is not so controlled it is more economical than other Fully Refined Grades.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade if their process will allow a Wax with a Wider -  less controlled Viscosity Band.

Other Applications Include:-

  • PVC Compounding/Colour and Black Masterbatch/Thermoplastic Road Marking/Petroleum Wax Blending/Cable Filling Compound
Features of the Grade are: Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC <=60cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness2d-mmASTM D1321
Dropping Point 116ºCASTM D3954
Whiteness Index (WI)>=40 ASTM E 313

Packaging & Storage

LP1022P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1022P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1400T – Fully Refined Pastilles – High Viscosity

LP1400T is a High Viscosity (300-400cps) Fully Refined HDPE derived wax offered in the form of white pastilles (Odorless).  

Applications and Benefits include:-

  • PVC Compounding/Filler & Colour Masterbatch/Cable Filling Compound/Thermoplastic Road Marking

Other Applications Include:-

  • Hot Melt Adhesive 
 

Main Benefits to note:  Capable of undergoing High Shear/Odorless/No Dust (pastille form)/ FDA approval

Features of the Grade are: High Viscosity - so capable of undergoing ''high shear''/Odorless/ Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties and Fully compliant with Many Regulations including FDA/REACH/RoHS etc. etc.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 300-400cpsASTM D3236
Dropping Point 116ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.94g/cm3ASTM D1505

Packaging & Storage

LP1400T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1400T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.