Masterbatch

Choose from our recommended Grades below
using the drop down menu

LP1020P Fully Refined Powder – Lowest Viscosity

LP1020P is our Lowest Viscosity (10-20 cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for the Lowest Viscosity requirement. Other options in our range include LP1040P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.
  This range of Fully Refined Waxes can also find applications in :-
  • PVC Compounding/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
 

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-20cpsASTM D3236
Dropping Point 113 to 118ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Melting Point 94,119 ºCDSC Peak
Whiteness Index (WI)>=45ASTM E313

Packaging & Storage

LP1020P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1020P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040P Fully Refined Powder – Medium Viscosity

LP1040P is our Medium Viscosity (20-40cps) ''Standard'' Fully Refined HDPE derived wax offered in the form of white powder.

 

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. Other options in our range include LP1020P/LP1040T (Pastilles) /LP1024P (Super clean and Harder)/LP1022P (economical but wider Viscosity range).  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance.

This range of Fully Refined Waxes can also find applications in :-

  • PVC Compounding/Masterbatch/Thermoplastic Road Marking/Masterbatch/Cable Filling/Rubber Compounding
   

Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 20-40cpsASTM D3236
Dropping Point 113-116ºCASTM D3954
Penetration Hardness<=2d-mmASTM D1321
Density0.94g/cm3ASTM D1505
Whiteness Index (WI)>=45ASTM E313

Packaging & Storage

LP1040P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1040P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1040T ‘Active Flow’ – Medium Viscosity in Pastille Form (Easy Handling)

LP1040T ''Active Flow'' is our Medium Viscosity (15-40cps) Fully Refined HDPE derived wax offered in the form of white Pastilles.  

Applications and Benefits include:-

  • Processing Aid/Additive for Film Extrusion/Extrusion Blow Moulding/Injection Moulding - Key Benefits include :- Easy to Handle (Dust Free)/Low Viscosity/Good Heat Stability/Highly Compatible with Polyolefin/Improve Flowability & Productivity/ Improve Colour Dispersion/ Reduce Processing Temperature and FDA compliant!
  • Hot Melt Adhesive - Customers opt for this grade for a Medium Viscosity requirement. It is easy to handle (Pastilles) and will be ''Dust Free'' as its not in powder form.  This grade will help Reduce Viscosity to promote wettability/Adjust Open and Set time/Enhance heat resistance
Other applications include :- PVC Compounding (External Lubricant for Rigid PVC)/Masterbatch/Thermoplastic Road Marking (reduce Viscosity of Hydrocarbon based formulations)  /Cable Filling/Rubber Compounding Features of the Grade are: High MP and Softening Point/Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 15-40cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness<=2d-mmASTM D1321
Dropping Point 113 to 118ºCASTM D3954
Whiteness Index (WI)>= 20 ASTM E313

Packaging & Storage

LP1040T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1040T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1024P Super Refined Powder Grade

LP1024P is a ''Super Refined''  PE wax derived from an HDPE process in the form of white powder. Consequently it is an extremely clean, Low Viscosity (10-40 cps) pretty hard (Penetration Index <1) Wax that has found admirers in the Hot Melt Adhesive Industry.   

Key Benefits recognised in the Hot Melt Adhesive Application include:-

  • Very Low Volatiles due to the Double Refining Process
  • Low Viscosity which promotes wettability
  • Adjust Open and Set time
  • Enhanced heat resistance - Best in Class Thermal Resistant grade with higher dropping point and hardness than other PE Waxes
 
  • Partial replacement of FT wax (e.g. m-PO base HMA for Packaging applications) for overall cost reduction.

This grade is also used in the Paints/ Coatings/Inks Industry in its Micronised form (Please ask for details)

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 10-40cpsASTM D3236
Dropping Point 116 to 120ºCASTM D3954
Penetration Hardness<=1d-mmASTM D1321
Density0.95g/cm3ASTM D1505
Whiteness Index>=45ASTM E313

Packaging & Storage

LP1024P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1024P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1022P Fully Refined Powder (Wide Viscosity)

LP1022P is a Wide Viscosity (<=60cps) Fully Refined HDPE derived wax offered in the form of white powder. As the Viscosity is not so controlled it is more economical than other Fully Refined Grades.

Applications and Benefits include:-

  • Hot Melt Adhesive - Customers opt for this grade if their process will allow a Wax with a Wider -  less controlled Viscosity Band.

Other Applications Include:-

  • PVC Compounding/Colour and Black Masterbatch/Thermoplastic Road Marking/Petroleum Wax Blending/Cable Filling Compound
Features of the Grade are: Low Viscosity/Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC <=60cpsASTM D3236
Density0.94g/cm3ASTM D1505
Penetration Hardness2d-mmASTM D1321
Dropping Point 116ºCASTM D3954
Whiteness Index (WI)>=40 ASTM E 313

Packaging & Storage

LP1022P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

LP1022P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

LP1400T – Fully Refined Pastilles – High Viscosity

LP1400T is a High Viscosity (300-400cps) Fully Refined HDPE derived wax offered in the form of white pastilles (Odorless).  

Applications and Benefits include:-

  • PVC Compounding/Filler & Colour Masterbatch/Cable Filling Compound/Thermoplastic Road Marking

Other Applications Include:-

  • Hot Melt Adhesive 
 

Main Benefits to note:  Capable of undergoing High Shear/Odorless/No Dust (pastille form)/ FDA approval

Features of the Grade are: High Viscosity - so capable of undergoing ''high shear''/Odorless/ Excellent Heat Resistance and Thermally Stability/High Hardness level/Excellent Chemical resistance/Highly compatible with other waxes/ Excellent Lubrication properties and Fully compliant with Many Regulations including FDA/REACH/RoHS etc. etc.

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @149ºC 300-400cpsASTM D3236
Dropping Point 116ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.94g/cm3ASTM D1505

Packaging & Storage

LP1400T is packaged in 25kgs bags and is supplied on shrink-wrapped pallets of 1500kgs each .

Product Safety

LP1400T is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2020P Powder

WD2020P is the Lowest Viscosity (200 cps) grade of our Virgin thermally cracked LDPE waxes

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers.  Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier  - Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding 
   

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @140ºC 150-250cpsASTM D3236
Softening Point 107ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.92g/cm3ASTM D1505

Packaging & Storage

WD2020P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

WD2020P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2040P Powder

WD2040P is a Virgin High Quality LDPE Medium Viscosity (400 cps) thermally cracked polyethylene wax - Very Popular in Masterbatch and Hot Melt Adhesive Applications

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers.  Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier  - Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding 
         

DATA SHEET

TYPICAL PROPERTIESVALUEUNITTEST METHOD
Viscosity @140ºC 350-450cpsASTM D3236
Softening Point 109ºCASTM D3954
Penetration Hardness2d-mmASTM D1321
Density0.92g/cm3ASTM D1505

Packaging & Storage

WD2040P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

WD2110P Powder

WD2110P - Highest Viscosity (1100 cps) and Mol Weight (2975 Mn) of any of our Virgin thermally cracked LDPE wax grades

Properties and Applications include:

  • Colour and Black Masterbatch - Dispersion Aid - Can be added to Masterbatch's to aid pigment dispersion and improve compatibility of Pigments and Fillers. The high Viscosity and Mol Wt will help aid dispersion on highly loaded products. Excellent pigment wettability.
 
  • Wax Blending - Compatibilizer and Viscosity Modifier - E.G. Blend with Natural Wax to improve surface hardness and softening Point e.g. Crayons/Candles
 
  • PVC Compound - Lubrication and Mould Release - Used as a rubber processing aid/external Lubricant for PVC processing/release agent. Excellent Lubrication
 
  • Hot Melt Adhesive - Aids Dispersion and compatibility
 
  • Rubber Compounding
   

DATA SHEET

PROPERTYVALUEUNITTEST METHOD
Viscosity @140ºC 1000-1200cpsASTM D3236
Softening Point 110ºCASTM D3954
Penetration Hardness1d-mmASTM D1321
Density0.92g/cm3ASTM D1505

Packaging & Storage

WD2110P is packaged in 20kgs bags and is supplied on shrink-wrapped pallets of 1400kgs each .

Product Safety

WD2110P is not classified as a hazardous material when exposure is controlled by using accepted industrial hygiene practices. Please contact us for further information and a copy of the Material Safety Data Sheet.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

FDA : This product meets the FDA requirements contained in the Code of Federal Regulations according to 21CFR 178.3720 Petroleum Wax, Synthetic and 21CFR 175.105 Adhesives.

EU10/2011 : This product meets the requirement for plastic materials and articles intended to come into contact with food as described in Commission Regulation (EU) No 10/2011 and its Amendments Commission Regulation (EU) No 1282/2011, 1183/2012, 202/2014, 174/2015, 1416/2016, 752/2017, 79/2018, 831/2018. Monomers used to manufacture this product  are listed in ‘Union List of Authorised Substances’ Annex I. No monomers, subject to restriction (Specific Migration Limit) are used in the manufacture of this product. There is no additive in this product.

REACH:  Polymers are exempt from REACH registration but Monomers that the Polymer is created from do have to be registered.  The Monomers for this product, Ethylene and  But-1-ene, are registered under REACH.  Please contact us for further information.

Oil Black 9S

High Quality Grade with Low Chlorine and Aniline Content.

DATA SHEET

PROPERTYVALUE
Volatile Matter (including water) <1.0%
Ash <2.0%
pH 7.0 - 9.0
Chlorine ContentLow content
Aniline ContentVery low content

APPLICATIONS

Masterbatch

Packaging & Storage

Oil Black 9S is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.

Oil Black SF

Oil Black SF

Low Chlorine/Low Aniline Grade. This particular grade of Nigrosine has  a mainly reduced Chlorine content and the Aniline content is also low.

DATA SHEET

PROPERTYVALUE
Volatile Matter (including water) <1.0%
Ash <2.0%
pH 7.0 - 9.0
Chlorine ContentVery low content
Aniline ContentVery low content

APPLICATIONS

Masterbatch

Packaging & Storage

Oil Black SF is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.

Oil Black F-7L

Very Low Anilene/Chlorine grade

This particular grade of Nigrosine has a lower Aniline content and Chlorine content compared to CAE (our Standard Grade).  Can be used in the Masterbatch industry with Nylon for compounding, Extrusion and Injection moulding glass fibre filled compounds.  End uses include (but not limited to) discerning Automotive companies who need a Top Quality Dye for refined applications.

DATA SHEET

PROPERTYVALUE
Volatile Matter (including water) <1.0%
Ash <2.0%
pH 6.0 - 8.0
Chlorine ContentVery low content
Aniline ContentVery low content

APPLICATIONS

Masterbatch

Packaging & Storage

Oil Black 7-FL is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.

Spirit Black CAE

Spirit Black CAE is the flagship SB7 grade from our range (Very Good Heat Stability at High Temperatures)  

Very high quality and used extensively in the Masterbatch industry with Nylon (PA6)  for Compounding, Extrusion and Injection moulding glass fibre filled compounds.

DATA SHEET

PROPERTYVALUE
Volatile Matter (including water) <1.0%
Ash <2.0%
pH 5.0 - 7.5
Aniline ContentLow content

APPLICATIONS

Masterbatch

Packaging & Storage

Spirit Black CAE is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.

Spirit Black MB

STANDARD product with the lowest PH level. Used with Phenol Resin.

DATA SHEET

PROPERTYVALUE
Volatile Matter (including water) <1.0%
Ash <2.0%
pH 4.0 - 6.0

APPLICATIONS

Masterbatch

Packaging & Storage

Spirit Black MB is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.

Black F-5C

Black F-5C is a Mixed Dye with Carbon Black and Anthraquinone.  It was developed to obtain a Piano Black Colour with a competitive price

Relatively new grade for applications including - Masterbatch industry with Nylon (PA6) for Compounding, Extrusion and Injection moulding glass fibre filled compounds.  Gives improved Heat and Light resistance and Excellent Jet-Black properties. Also used with ABS / AS and PC to give a 'Complementary Colour'. We also have BLACK  F-5D which is without Carbon Black - this is for customers who need a Darker Black Colour.    

DATA SHEET

PROPERTYVALUE
Water Content <3.0%
Ash <8.0%
pH 4.5 - 6.5

APPLICATIONS

Masterbatch

Packaging & Storage

Black F-5C is packaged in 15kgs bags and is supplied on pallets of 420kgs each.

Product Safety

Please contact us for further information and a copy of the Material Safety Data.

Compliance

Note: The properties of each grade are for Guidance only.  A specification can be agreed and sent upon request. 

REACH:  Pre-Registered for REACH.  Please contact us for further information.